Line follower robot with L298N and TCRT5000
The classic robotics starter: a two-wheeled car that tracks a black line on its own.
Shop by category
Shop all componentsRobot sumo is a favourite at school and college tech fests. Two infrared sensors underneath watch for the white edge of the black ring; the ultrasonic sensor at the front looks for the opponent. The robot waits five seconds after switch-on (the competition rule), spins to search, charges when it sees the other robot within 40 cm, and reverses and turns whenever a sensor reaches the edge.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Compact MOSFET motor driver that wastes far less power than an L298N, so battery robots run longer and the motors get more voltage.
Two infrared reflectance sensors: black tape reflects little IR, white floor reflects a lot, so each output tells you which side the line is on.
Sends a 40 kHz ultrasonic ping and times the echo to measure distance from 2 cm to about 4 m.
Raises the cell's 3.0–4.2 V to a steady 5 V for the board
Follow the colours: red is power, dark grey is ground, blue is a signal.
Battery + goes to the TB6612 VM pin and battery − to GND; join that GND to the board GND. Power the Uno and the TB6612 VCC from a 5 V power bank or a buck converter. Set the boost converter to 5.0 V with a multimeter before connecting the board. Cell + → boost IN+, cell − (TP4056 OUT−) → boost IN−, then boost OUT+ → board 5V pin and OUT− → GND. A bare 18650 (3.0–4.2 V) cannot run a 5 V board by itself.
mini_sumo_robot.inoVerify & upload in Electrolark// Mini sumo robot
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "mini-sumo-robot"
// ---- pins ----
const uint8_t ENA = 3;
const uint8_t IN1 = 2;
const uint8_t IN2 = 4;
const uint8_t ENB = 5;
const uint8_t IN3 = 6;
const uint8_t IN4 = 7;
const uint8_t STBY_PIN = 8;
const uint8_t LINE_LEFT = 12;
const uint8_t LINE_RIGHT = 13;
const uint8_t TRIG_PIN = 9;
const uint8_t ECHO_PIN = 10;
// ---- latest readings ----
float distCm = 0;
const int ATTACK = 230, SEARCH = 120;
const float SEE_CM = 40; // opponent closer than this: charge
const bool EDGE_IS_LOW = true; // TCRT5000 reads LOW over the white edge; set false if yours is the other way
// speed: -255 (full reverse) to 255 (full forward)
void drive(int left, int right) {
digitalWrite(IN1, left >= 0 ? HIGH : LOW);
digitalWrite(IN2, left >= 0 ? LOW : HIGH);
analogWrite(ENA, constrain(abs(left), 0, 255));
digitalWrite(IN3, right >= 0 ? HIGH : LOW);
digitalWrite(IN4, right >= 0 ? LOW : HIGH);
analogWrite(ENB, constrain(abs(right), 0, 255));
}
float readDistanceCm() {
digitalWrite(TRIG_PIN, LOW);
delayMicroseconds(2);
digitalWrite(TRIG_PIN, HIGH);
delayMicroseconds(10);
digitalWrite(TRIG_PIN, LOW);
unsigned long us = pulseIn(ECHO_PIN, HIGH, 30000UL); // 30 ms timeout, about 5 m
if (us == 0) return -1; // no echo
return us * 0.0343f / 2.0f;
}
void setup() {
Serial.begin(115200);
pinMode(ENA, OUTPUT); pinMode(IN1, OUTPUT); pinMode(IN2, OUTPUT);
pinMode(ENB, OUTPUT); pinMode(IN3, OUTPUT); pinMode(IN4, OUTPUT);
pinMode(STBY_PIN, OUTPUT); digitalWrite(STBY_PIN, HIGH);
pinMode(LINE_LEFT, INPUT);
pinMode(LINE_RIGHT, INPUT);
pinMode(TRIG_PIN, OUTPUT);
pinMode(ECHO_PIN, INPUT);
delay(5000); // competition rule: wait 5 seconds after start
}
void loop() {
bool edgeL = (digitalRead(LINE_LEFT) == LOW) == EDGE_IS_LOW;
bool edgeR = (digitalRead(LINE_RIGHT) == LOW) == EDGE_IS_LOW;
if (edgeL || edgeR) { // at the ring edge: back off and turn away
drive(-200, -200); delay(300);
if (edgeL) drive(180, -180); else drive(-180, 180);
delay(250);
return;
}
distCm = readDistanceCm();
if (distCm > 0 && distCm < SEE_CM) drive(ATTACK, ATTACK); // opponent ahead: push
else drive(SEARCH, -SEARCH); // spin to search
delay(20);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
STBY is floating or LOW: wire it to a pin held HIGH (the sketch does this) or to VCC.
Swap that motor's two wires on the driver.
Lower the sensor to 5–10 mm from the surface and re-tune the trimmer until its LED switches between the light and dark surface.
TRIG and ECHO are swapped, or the sensor has no 5 V. Swap the two signal wires and check VCC.
Average several readings and keep wires short. Two HC-SR04s pinging at once will confuse each other.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
11 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, TB6612FNG Dual Motor Driver Module, TCRT5000 Dual Channel Line Tracking Sensor Module, HC-SR04 Ultrasonic Range Finder Sensor Module, 2WD Smart Robot Car Chassis Kit, 2 × 18650 Battery Holder, 2 × 18650 Li-ion Rechargeable Cell 2600mAh, MT3608 Mini Boost Converter Module, Solderless Breadboard (830 points), plus 1 more. Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 4–5 hours. The build on this page has 10 steps.
No. This page has the complete, tested code (mini_sumo_robot.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,260 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Infrared reflectance sensing; MOSFET H-bridges and standby pins; Time-of-flight measurement with sound.
Ideas that reuse this build: Edge-avoiding robot and Line follower with TB6612. They are listed under Take it further on this page.
The classic robotics starter: a two-wheeled car that tracks a black line on its own.
A robot that looks left and right with its ultrasonic "head" and picks the clearest way.
Roams a tabletop without ever driving off the edge.
Drive a 4WD car from your Android phone over Bluetooth.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.