Automatic dusk-to-dawn light
Lights switch on by themselves at dusk and off again in the morning.
Shop by category
Shop all componentsPair your phone with the HC-05, open any Bluetooth serial terminal app and send your PIN followed by #. If it matches, the relay powers the solenoid bolt for five seconds. Three wrong tries lock it out for a minute to slow down guessing. Good for a tool cupboard, a store room or a model of a smart lock.
A hobby lock, not a security product. Keep a mechanical key or manual release so nobody can be locked in or out.
Keep to low-voltage loads unless a qualified electrician wires the mains side in an earthed, closed enclosure.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Classic Bluetooth serial module: your phone sends characters and the board receives them as if over a USB cable.
An electrically isolated switch that lets a 3.3/5 V pin turn a 12 V (or mains) load on and off.
Follow the colours: red is power, dark grey is ground, blue is a signal.
The 12 V adapter feeds the solenoid through the relay contacts, with a 1N4007 diode across the solenoid (stripe to +). Power the Uno from USB or the adapter through its DC jack.
bluetooth_pin_door_lock.inoVerify & upload in Electrolark// Bluetooth phone PIN door lock
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "bluetooth-pin-door-lock"
#include <SoftwareSerial.h>
// ---- pins ----
const uint8_t BT_RX = 2;
const uint8_t BT_TX = 3;
const uint8_t RELAY_PIN = 4;
const bool RELAY_ACTIVE_LOW = true; // most relay modules switch on when IN is LOW
SoftwareSerial btSerial(BT_RX, BT_TX);
const char PIN_CODE[] = "4729"; // change this before you fit the lock
const unsigned long OPEN_MS = 5000;
char typed[12]; int typedLen = 0;
int wrongTries = 0;
unsigned long lockedUntil = 0;
void setRelay(bool on) { digitalWrite(RELAY_PIN, (on != RELAY_ACTIVE_LOW) ? HIGH : LOW); }
void setup() {
Serial.begin(115200);
pinMode(RELAY_PIN, OUTPUT);
setRelay(false);
btSerial.begin(9600);
setRelay(false);
}
void loop() {
if (!btSerial.available()) return;
char ch = btSerial.read();
if (ch == '\r' || ch == '\n') return;
if (ch != '#') { if (typedLen < 11) typed[typedLen++] = ch; return; } // # ends the code
typed[typedLen] = 0; typedLen = 0;
if (millis() < lockedUntil) { btSerial.println(F("Too many tries, wait a minute")); return; }
if (strcmp(typed, PIN_CODE) == 0) {
wrongTries = 0;
btSerial.println(F("Unlocked"));
setRelay(true); delay(OPEN_MS); setRelay(false); // solenoid pulls the bolt back for 5 s
btSerial.println(F("Locked"));
} else {
wrongTries++;
btSerial.println(F("Wrong code"));
if (wrongTries >= 3) { lockedUntil = millis() + 60000; wrongTries = 0; } // slow down guessing
}
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check TXD→board RX and RXD→board TX (crossed). The module LED blinks slowly once connected.
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
10 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, HC-05 6-Pin Bluetooth Serial Module with Button, 5V Relay Module with Optocoupler (1 channel), Resistor Assortment Kit (30 Values), 12V Electric Solenoid Door / Cabinet Lock, DC Power Adapter 12V 2A (5.5x2.1mm), Diodes (Pack of 10, 1N4007), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2–3 hours. The build on this page has 8 steps.
No. This page has the complete, tested code (bluetooth_pin_door_lock.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,228 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Isolation, relays and switching higher-power loads; UART serial communication.
Ideas that reuse this build: Keypad door lock and RFID door lock. They are listed under Take it further on this page.
Lights switch on by themselves at dusk and off again in the morning.
A precise thermostat that keeps tropical fish at a steady 25–26 °C.
Starts the pump when the tank runs low and stops it when it is full.
Tap a hidden pad to switch a lamp on or off, even through a wooden desk.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.