Shop by category
Shop all componentsFDM printer · 5 checks, easiest first
The first layer drags around, curls up, or the print comes loose part-way and turns into spaghetti.
Check 1 of 5
Most first-layer problems come from the nozzle being too high or too low. Too high and the line is round and lifts off; too low and it scrapes, gets thin and see-through, or the extruder clicks.
| First layer height | 0.2 mm (for a 0.4 mm nozzle) |
|---|---|
| First layer speed | 15 to 30 mm/s |
| Z offset steps | 0.02 to 0.05 mm at a time |
Check 2 of 5
Finger grease and old glue are the most common reason a print that used to stick no longer does.
Check 3 of 5
If the bed is not the same distance from the nozzle everywhere, one corner sticks and another does not.
Check 4 of 5
Each material needs a warm enough bed to stay soft at the bottom and stick.
| PLA | Nozzle 190 to 220 °C, bed 50 to 60 °C |
|---|---|
| PETG | Nozzle 230 to 250 °C, bed 70 to 85 °C |
| ABS / ASA | Nozzle 240 to 260 °C, bed 90 to 110 °C, enclosure |
| TPU | Nozzle 210 to 230 °C, bed 40 to 60 °C |
Check 5 of 5
Small or tall parts have little contact area, so they get knocked off by the nozzle.
FDM printer · 4 checks, easiest first
The bottom corners of the part curl up off the bed, often getting worse as the print grows.
Check 1 of 4
Plastic shrinks as it cools. If the top cools faster than the bottom, it pulls the corners up.
Check 2 of 4
Finger grease and old glue are the most common reason a print that used to stick no longer does.
Check 3 of 4
A warmer bed keeps the bottom layers soft and stuck; a brim adds grip at the corners.
Check 4 of 4
Most first-layer problems come from the nozzle being too high or too low. Too high and the line is round and lifts off; too low and it scrapes, gets thin and see-through, or the extruder clicks.
| First layer height | 0.2 mm (for a 0.4 mm nozzle) |
|---|---|
| First layer speed | 15 to 30 mm/s |
| Z offset steps | 0.02 to 0.05 mm at a time |
FDM printer · 4 checks, easiest first
Thin strands like a spider web stretch across gaps between towers or parts.
Check 1 of 4
Filament absorbs moisture from the air. Wet filament pops and oozes, which causes strings that no setting can remove. PETG, TPU and nylon are the worst.
| PLA | 45 to 50 °C, 4 to 6 h |
|---|---|
| PETG | 60 to 65 °C, 4 to 6 h |
| TPU | 50 to 55 °C, 6 to 8 h |
| Nylon | 70 to 80 °C, 8 to 12 h |
Check 2 of 4
Retraction pulls the filament back before a travel move, so the nozzle does not leak.
| Direct drive | 0.5 to 2 mm at 30 to 45 mm/s |
|---|---|
| Bowden | 4 to 7 mm at 40 to 60 mm/s |
Check 3 of 4
Hotter plastic is runnier and leaks more during travel.
Check 4 of 4
Fewer and faster moves across open space mean less time to ooze.
FDM printer · 4 checks, easiest first
The printer moves but no plastic comes out, or only a little, often with the extruder clicking.
Check 1 of 4
Many 'clogs' are an empty spool, a tangled spool, a cold nozzle or a nozzle pressed onto the bed.
Check 2 of 4
A cold pull removes burnt bits and dust stuck inside the nozzle without taking it apart.
Check 3 of 4
Hard blockages or a worn nozzle need cleaning from below or a new nozzle.
Check 4 of 4
If the hotend's cooling fan fails, filament softens too high up and jams. This often happens on long PLA prints in a warm room.
FDM printer · 4 checks, easiest first
Missing lines, gaps in the top surface, see-through walls or parts that break easily.
Check 1 of 4
A spool that binds, a kinked tube or a partial clog all reduce flow.
Check 2 of 4
Each hotend can only melt a certain amount of plastic per second. Above that, walls get thin.
Check 3 of 4
If the extruder pushes less filament than it thinks, every line is thin.
Check 4 of 4
Worn or dirty gears slip on the filament.
FDM printer · 4 checks, easiest first
A repeated click from the extruder motor, and the filament has a chewed flat spot.
Check 1 of 4
Most first-layer problems come from the nozzle being too high or too low. Too high and the line is round and lifts off; too low and it scrapes, gets thin and see-through, or the extruder clicks.
| First layer height | 0.2 mm (for a 0.4 mm nozzle) |
|---|---|
| First layer speed | 15 to 30 mm/s |
| Z offset steps | 0.02 to 0.05 mm at a time |
Check 2 of 4
The extruder skips when it cannot push plastic through the nozzle fast enough.
Check 3 of 4
A partial clog makes the extruder fight back pressure.
Check 4 of 4
Too much tension crushes filament; too little lets it slip.
FDM printer · 3 checks, easiest first
The print suddenly steps sideways at one height, like a staircase, and continues offset.
Check 1 of 3
A loose belt or a pulley grub screw that has slipped lets the axis lose position.
Check 2 of 3
If the nozzle hits a curled-up edge, the head can be knocked out of place.
Check 3 of 3
Stepper motors skip steps if asked to move a heavy axis faster than they can.
FDM printer · 3 checks, easiest first
The first few layers are wider than the rest, so parts do not fit together.
Check 1 of 3
A first layer squashed too much spreads outwards.
Check 2 of 3
A very hot bed keeps the bottom layers soft while the weight above pushes them out.
Check 3 of 3
Most slicers can shrink the first layer slightly to cancel the bulge.
FDM printer · 2 checks, easiest first
Curled or sagging edges on overhangs, bridges that hang down, rough undersides.
Check 1 of 2
Overhangs need the plastic to set quickly. A weak, blocked or misaligned fan causes droop.
Check 2 of 2
More time and cooler plastic help each line set before the next.
FDM printer · 2 checks, easiest first
Wavy echoes repeat on the surface just after sharp corners or text.
Check 1 of 2
Loose belts and wobbly frames vibrate after every sharp change of direction.
Check 2 of 2
Lower acceleration means less force to shake the frame; input shaping cancels the vibration.
FDM printer · 3 checks, easiest first
Horizontal cracks between layers, often on tall parts; parts snap along a layer line.
Check 1 of 3
Layers bond only if the new plastic is hot enough to melt into the one below.
Check 2 of 3
Too much fan or a cold draft cools each layer before the next arrives.
Check 3 of 3
Thin lines and steam bubbles both weaken layer bonds.
Resin printer · 4 checks, easiest first
The build plate comes up empty or with only supports, and a cured layer is stuck to the FEP film in the vat.
Check 1 of 4
If the plate is not flat to the screen, the first layers do not bond to it.
Check 2 of 4
The first layers need much longer exposure than normal layers to grip the plate.
| Normal layer (mono LCD) | Typically 1.5 to 3 s, depends on resin |
|---|---|
| Bottom layers | 4 to 8 |
| Bottom exposure | Typically 20 to 40 s |
Check 3 of 4
Below about 20 °C resin gets thick and cures poorly.
Check 4 of 4
Cured bits floating in the vat or a cloudy, stretched FEP film cause more failures.