Shop by category
Shop all componentsA bus that carries data and timing on a single wire plus ground, with each device identified by a unique 64-bit address. Used by the DS18B20 temperature sensor.
Used in DS18B20 Waterproof Temperature Sensor · How to Choose a Temperature Sensor for Arduino and ESP32 · SHT3x, SHT4x and Digital Humidity Sensors
Most IR remotes switch their LED on and off at 38 kHz. An IR receiver filters that frequency and outputs the on/off pattern.
Used in IR Remote Receivers
A way to send a sensor reading as a current between 4 and 20 mA. It resists noise over long cables, and a reading below 4 mA signals a broken wire.
Used in Weather Station Sensors · Pressure Transducers and Transmitters · Inclinometers and Tilt Angle Sensors
Automatic baseline correction. Some CO2 sensors assume the lowest reading each day is fresh air (about 420 ppm) and reset to it. It drifts if the room is never aired.
Used in CO2 Sensors
An encoder that reports the exact shaft angle as a code, so the position is known immediately after power-up with no homing.
A sensor that measures acceleration, including gravity, along one or more axes; used to detect tilt, vibration and movement.
Used in MPU6050 Accelerometer and Gyroscope · Vibration, Shock and Tilt Sensors (SW-420, SW-520D) · Accelerometers
Newer release films for resin vats with higher strength and better peel than FEP, used on faster printers.
High-frequency sound waves released by cracks, leaks, friction and impacts in materials. AE sensors are piezo sensors tuned to listen for them.
Used in Piezo Sensors and Discs
A signal that is 'on' when pulled to 0 V. Many relay modules switch on when their input is LOW.
Used in Relay Modules · IR Obstacle Sensor Module · Optocouplers
Analog-to-digital converter: turns a voltage into a number. A 10-bit ADC gives 0 to 1023; a 12-bit ADC gives 0 to 4095.
Used in ESP32 Guide · Raspberry Pi Pico Guide · ESP8266 NodeMCU
An LED with a built-in controller, such as the WS2812B, so each LED on a chain can be set individually from one data pin.
Used in WS2812B Addressable LEDs (NeoPixel) · Drone Navigation Lights, Strobes and Lost-Model Alarms
Aircraft broadcast their position on 1090 MHz. An SDR with a suitable antenna can receive and plot them.
Used in SDR Receivers
Attitude and heading reference system: an IMU with fusion software that outputs roll, pitch and heading.
Used in Magnetometers and 9-Axis IMUs
A nozzle that blows a stream of air along the laser beam. It clears smoke from the cut, lowers flare-ups and keeps the lens clean.
Used in Laser Engraver Accessories
A signal whose voltage varies continuously, such as a sensor output of 0 to 3.3 V, rather than switching only between HIGH and LOW.
Used in Soil Moisture Sensors · ADCs Explained · Rain and Water Level Sensor Modules
The anode is the positive terminal of a diode or LED and the cathode the negative. Current flows from anode to cathode.
Used in LEDs Explained · Diodes Explained · RGB LEDs
Access point name: the setting that tells a cellular modem which gateway on the mobile network to use for data. Your SIM operator lists it.
Used in 4G LTE Modules for IoT · Industrial 4G Routers and IoT Gateways
A 555 timer mode with no stable state: the output switches high and low continuously, making an oscillator.
Used in 555 Timer IC
Text commands that start with AT, sent over a serial port to configure modules such as Bluetooth, Wi-Fi and GSM radios.
Used in ESP-01 / ESP-01S ESP8266 Module · HC-06 Bluetooth module · ESP8266 and ESP8285 Modules
A school lab set up under the Atal Innovation Mission where students tinker with electronics, robotics, 3D printing and tools to build their own ideas.
Used in Atal Tinkering Lab (ATL) · ATL Equipment Packages P1 to P4 · ATL Package 1
The voltage a spinning motor generates that opposes the supply. It reduces current as the motor speeds up.
Used in DC Motors Explained · Brushless Motor KV, Stator Size and Propeller Sizing Explained · ESCs Explained
Slack in a belt, screw or gear train that makes a machine lose motion when it changes direction.
Used in Laser Engraver Accessories
Charging each cell of a LiPo pack to the same voltage through the balance connector, so no cell is overcharged.
Used in LiPo Chargers, Smoke Stoppers and Battery Safety for Drones
The speed of a serial link in bits per second. Both ends must use the same value; 9600 and 115200 are the usual defaults.
Used in HC-05 Bluetooth Module · NEO-6M GPS Module · DFPlayer Mini MP3 Module
The Raspberry Pi pin naming that uses the Broadcom chip's GPIO numbers (GPIO 17, GPIO 27) instead of the physical header positions.
Used in Raspberry Pi GPIO Pinout
A constant that describes how steeply an NTC thermistor's resistance falls as temperature rises, quoted in kelvin (for example 3950 K). Used in the simple beta equation.
Used in NTC Thermistors
A tiny voltage produced by the body, such as the heart (ECG, about 1 mV), muscle (EMG) or brain (EEG). It needs an instrumentation amplifier before an ADC can read it.
Used in ECG, EMG and EEG Sensors
Bipolar junction transistor (NPN or PNP), controlled by a small base current. Examples: BC547, 2N2222.
Used in Transistors and MOSFETs as Switches · Schematic Symbols
Bluetooth Low Energy: the low-power Bluetooth profile used by phones, fitness bands and the ESP32. It is not compatible with the HC-05's Bluetooth Classic serial profile.
Used in HC-05 Bluetooth Module · ESP32 vs ESP8266 · Wi-Fi vs Bluetooth vs LoRa vs Zigbee
A Bluetooth LE device's broadcast of its name and data so that phones can find it before connecting.
Used in Bluetooth LE Modules · BLE Beacons
Firmware families that run on drone ESCs. They set motor timing, direction and protocol; AM32 is an open-source option.
Used in FC and ESC Stacks and AIO Boards
Battery management system: a board that protects lithium cells from over-charge, over-discharge and over-current, and may balance cells in a pack.
Used in Li-ion, 18650 and LiPo Batteries · Series and Parallel Circuits · TP4056 Charger Module
A DC-DC converter that raises voltage, for example 3.7 V to 5 V.
Used in Buck and Boost Converters · Inductors Explained · MT3608 boost converter
A small program stored on a microcontroller that lets you upload new code over USB or serial without a dedicated programmer.
Used in Arduino Nano · Arduino Mega 2560 · USB to TTL Serial Adapters
A 3D printer extruder layout where the motor sits on the frame and pushes filament through a PTFE tube to the hot end. Lighter head, but harder with flexible filament.
Used in PLA vs PETG vs ABS vs TPU · 3D Printer Nozzles · 3D Printer Hotends and Extruders Explained
A reusable board with spring contacts for building circuits without soldering.
Used in How to Use a Breadboard · Jumper Wires and Dupont Connectors · The Starter Electronics Toolkit
A DC-DC converter that lowers voltage efficiently, for example 12 V to 5 V.
Used in Buck and Boost Converters · Voltage Regulators · How to Power an Arduino or ESP32 from Batteries
The surface a 3D print grows on. Common types are smooth or textured PEI on spring steel, glass and coated aluminium.
The preheating period an MQ gas sensor needs (usually 24 to 48 hours the first time, minutes afterwards) before its readings settle.
Used in MQ Gas Sensors · MQ-2 gas sensor · MQ-135 air quality sensor
Heating a plaster mould with a castable resin or wax pattern in it so the pattern burns away cleanly, leaving a cavity for molten metal.
Used in Engineering Resins
For batteries, the charge or discharge current relative to capacity. 1C on a 2000 mAh cell is 2 A.
Used in Li-ion, 18650 and LiPo Batteries · TP4056 Charger Module · Drone Parts Explained
Measuring a sensor against known conditions so its raw numbers can be converted into meaningful values, such as dry and wet readings for a soil sensor.
Used in Soil Moisture Sensors · Line Follower Robot · 3D Printer Bed Levelling and First-Layer Fixes
A two-wire differential network used in vehicles, drones and machines. Many nodes share one pair of wires and messages are prioritised by ID.
Used in CAN Bus Basics
A capacitor's ability to store charge, measured in farads (F); hobby parts are usually in pF, nF or µF.
Used in Capacitors Explained · Series and Parallel Circuits · Soil Moisture Sensors
A touchscreen that senses a fingertip by the change it causes in an electric field. It needs only a light touch and supports multi-touch.
Used in ESP32-S3 Touchscreen Boards
Measurement category (CAT I to IV) that tells you where a multimeter can be used safely. CAT II covers household sockets.
Used in How to Use a Multimeter
A gas sensor that burns flammable gas on a heated bead; the temperature rise is read as a concentration up to the lower explosive limit (LEL).
Used in Winsen Gas Sensor Modules
Constant-current then constant-voltage charging, the method for lithium cells: charge at fixed current until 4.2 V, then hold 4.2 V while current tapers.
Used in Li-ion, 18650 and LiPo Batteries · TP4056 Charger Module · LiPo Batteries for Drones
A Texas Instruments sub-GHz transceiver chip that supports 315, 433, 868 and 915 MHz with several modulations and an SPI interface.
Used in CC1101 and Sub-GHz Transceivers
Filaments filled with carbon fibre (CF) or glass fibre (GF). They are stiffer and more heat resistant but abrasive, so they need a hardened nozzle.
Carrier-grade NAT: mobile networks often share one public address between many SIM cards, so you cannot connect to a SIM directly from the internet.
A circuit that turns the tiny charge from a piezo sensor into a usable voltage, with a stable gain and low drift.
Used in Piezo Sensors and Discs
Radio waves that spin clockwise (right-hand, RHCP) or anticlockwise (left-hand, LHCP). Transmit and receive antennas must use the same hand or signal drops sharply.
Used in FPV Antennas · FPV Goggles and Video Receivers
Complementary metal-oxide-semiconductor: the low-power transistor technology used in 74HC and CD4000 logic and in most microcontrollers. CMOS inputs draw almost no current but must never float.
Used in Logic Gate ICs · Analog Multiplexers · ESD Safety
Two types of image sensor. CMOS is cheap, fast and low power and dominates cameras; CCD is used in some scientific and line-scan sensors.
Used in Camera Image Sensors Explained
Common-mode rejection ratio: how well an amplifier ignores noise that appears equally on both inputs, such as mains hum picked up by the body.
Used in ECG, EMG and EEG Sensors
A dull, grainy solder joint made with too little heat, often unreliable.
Used in How to Solder Electronics · Perfboard and Stripboard · The Starter Electronics Toolkit
A 7-segment or RGB LED where all anodes share one pin connected to the supply, and each segment is lit by pulling its cathode LOW.
Used in 7-Segment Displays · RGB LEDs · LED Strips
A 7-segment or RGB LED where all cathodes share one pin connected to ground, and each segment is lit by driving its anode HIGH.
Used in 7-Segment Displays · MAX7219 LED Dot Matrix · RGB LEDs
A circuit that compares two voltages and outputs HIGH or LOW depending on which is larger. Sensor modules use one (often an LM393) to produce their digital output.
Used in IR Obstacle Sensor Module · MQ Gas Sensors · LDR Light Sensors
A simple way to combine gyroscope and accelerometer readings into a stable angle by blending their strengths.
A complete, low-resistance electrical path between two points. A multimeter's continuity mode beeps when it finds one.
Used in How to Use a Breadboard · How to Use a Multimeter · Jumper Wires and Dupont Connectors
A chip that measures the current flowing into and out of a battery and adds it up, to track how much charge is left.
Used in Battery Monitors and Fuel Gauges
When a gas sensor also responds to gases other than the one it is meant to measure, giving false readings.
Used in Electrochemical Gas Sensors · Winsen Gas Sensor Modules
Crossfire serial protocol used by ExpressLRS and TBS receivers to send channels and telemetry to the flight controller on one wire.
Used in RC Receivers
Camera Serial Interface, the ribbon-cable connector that carries camera data into a Raspberry Pi.
Used in Raspberry Pi Camera Modules · Raspberry Pi Displays, Touchscreens and HDMI Adapters · TinyML and AI Vision Kits
The flow of electric charge through a circuit, measured in amperes (A) or milliamps (mA). It is what heats wires and drains batteries.
Used in Ohm's Law and Power · AC vs DC · Choosing a Power Supply
Digital-to-analog converter: turns a number into a real voltage. The ESP32 has two 8-bit DACs; the Uno has none and uses PWM instead.
Used in PWM Explained · DFPlayer Mini MP3 Module · I2S Microphones and Audio on ESP32
Two bipolar transistors connected so the first drives the second, giving very high current gain from a small input current, at the cost of a higher voltage drop of about 1 V.
Used in ULN2003 Darlington Array
Antenna gain in decibels compared with an ideal antenna that radiates equally in all directions. Higher gain concentrates signal in some directions at the expense of others.
Used in USB Wi-Fi and Bluetooth Adapters for Raspberry Pi and PCs · Antennas and RF Connectors · Choosing an RC Transmitter for Drones and Models
Filtering the rapid on-off bouncing of a mechanical switch so one press counts once.
Used in PIR Motion Sensor (HC-SR501) · Pull-Up and Pull-Down Resistors · Push Buttons with Arduino
A small capacitor, usually 100 nF, placed next to an IC's power pins to supply short current bursts and block noise.
Used in Capacitors Explained · nRF24L01 2.4 GHz Radio · A4988 vs DRV8825 vs TMC2209
A low-power mode where most of a microcontroller is switched off, cutting current to microamps between tasks.
Used in ESP32 Guide · ESP8266 NodeMCU · Arduino vs Raspberry Pi
The temperature at which air becomes saturated and water starts to condense. It is calculated from temperature and humidity.
The insulating material between a capacitor's plates. Ceramic types such as X7R and Y5V behave differently with temperature and voltage.
Used in Capacitor Code Chart
The difference between two pressures measured by one sensor with two ports, used for airflow, filter checks and flow meters.
Used in MEMS and Differential Pressure Sensors · Airspeed and Telemetry Sensors for Drones and Planes
Dual in-line package: a chip with two rows of pins 2.54 mm apart, designed to fit breadboards and through-hole PCBs.
Used in How to Use a Breadboard · Perfboard and Stripboard · PCB Basics
A 3D printer extruder layout where the motor sits on the print head and feeds filament straight into the hot end. Best for flexible filaments like TPU.
Used in PLA vs PETG vs ABS vs TPU · 3D Printer Nozzles · 3D Printer Hotends and Extruders Explained
Goggles or a receiver with two antennas and two radios that pick the stronger signal automatically.
Used in FPV Goggles and Video Receivers
A CAN bus protocol used by ArduPilot and PX4 to connect GPS, compass, ESC and other devices with only two data wires.
Used in Pixhawk and ArduPilot Autopilots · XT30, XT60 and Drone Connectors · Airspeed and Telemetry Sensors for Drones and Planes
The minimum difference between a linear regulator's input and output for it to stay in regulation.
Used in Voltage Regulators · How to Power an Arduino or ESP32 from Batteries · How to Read a Datasheet
A digital protocol between flight controller and ESC. It sends exact throttle values with error checking, with speeds from DShot150 to DShot1200.
Used in FC and ESC Stacks and AIO Boards
Display Serial Interface: the ribbon-cable connector on Raspberry Pi boards used for official touch displays.
Used in Raspberry Pi Displays, Touchscreens and HDMI Adapters
Receivers that use two signals from each satellite, which cancels part of the atmospheric error and improves accuracy in cities.
Used in GPS and GNSS Modules
A microcontroller with two CPU cores, for example a Cortex-M7 and a Cortex-M4, that can run separate tasks at the same time.
Used in Official Arduino Boards Compared
The percentage of time a PWM signal is high. 50% duty is on half the time.
Used in Servo Motors Guide · LEDs Explained · 555 Timer IC
The standard sets of preferred values (E12, E24, E96) that resistors and capacitors are made in, such as 1.0, 1.2, 1.5, 1.8, 2.2, 2.7, 3.3, 3.9, 4.7, 5.6, 6.8, 8.2.
Used in Resistor Colour Code Chart
How well a liquid or soil moisture carries current. It rises with dissolved salts and is used as a quick check of salinity and fertiliser level.
Used in Soil Sensors
The open-source firmware that runs on most modern hobby transmitters, with model memories, mixes, telemetry screens and Lua scripts.
Output power divided by input power. A 90% efficient converter loses 10% as heat.
Used in Buck and Boost Converters · PAM8403 and Other Audio Amplifier Modules · Inductors Explained
A small, cheap condenser microphone with a permanently charged film and a built-in transistor amplifier, needing a bias voltage to work.
Used in Sound Sensor and Microphone Modules Explained · I2S Microphones and Audio on ESP32 · Voice Recognition and Recording Modules (ISD1820, LD3320)
A sealed sensor in which the target gas causes a small current to flow between electrodes. The current is proportional to gas concentration.
Used in Electrochemical Gas Sensors
How well a surface gives off infrared heat, from 0 to 1. Infrared thermometers assume a value (often 0.95); shiny metal reads far too low.
Used in Thermal Cameras · Thermal Imaging Modules · MLX90614 (GY-906) Non-Contact Thermometer
Soldered flash storage on a module. It is more durable than an SD card and boots faster.
Used in Raspberry Pi Compute Modules · Alternatives to Raspberry Pi · IP KVM
A closed cabinet around a 3D printer that holds in heat and blocks drafts, which helps ABS and ASA print without warping.
Used in 3D Printer Enclosures
The common standard for passive UHF RFID tags and readers (ISO 18000-63). Each tag carries a unique EPC number.
Used in RFID Readers and Tags
Electronic speed controller: the driver that turns a brushless motor by switching its three phases, taking a throttle signal from the flight controller or receiver.
Used in Drone Parts Explained · Brushless Motor KV, Stator Size and Propeller Sizing Explained · ESCs Explained
An ESP8266 chip with 1 MB of flash memory built into the same package, so a module needs no separate flash chip. It runs the same code as the ESP8266.
Used in ESP8266 and ESP8285 Modules
Equivalent series resistance: the small internal resistance of a capacitor that causes heating and ripple.
Used in Capacitors Explained · Capacitor Code Chart · ESCs Explained
An open-source radio link for RC models with very low latency and long range, available on 2.4 GHz and sub-GHz bands. Radio and receiver must both use ELRS.
Used in Choosing an RC Transmitter for Drones and Models · RC Receivers
What the receiver tells the flight controller to do when the radio link is lost, such as cut throttle, hold position or return home.
Used in Choosing an RC Transmitter for Drones and Models · Pixhawk and ArduPilot Autopilots · RC Receivers
Fused deposition modelling: the common 3D printing method that melts filament and lays it down layer by layer.
Used in PLA vs PETG vs ABS vs TPU · 3D Printer Nozzles · 3D Printer Bed Levelling and First-Layer Fixes
A add-on board that stacks on an Adafruit Feather development board, adding things like displays, radios, motor drivers and SD cards.
Routing part of an amplifier's output back to its input. Negative feedback through resistors sets an op-amp's gain precisely.
Used in Op-Amps for Beginners · Motor Encoders and Speed Feedback · Serial Bus Servos
The clear, non-stick sheet at the bottom of a resin vat. The cured layer peels from it on each lift; it is a wear part.
How wide a scene a lens and sensor can see, given in degrees. A shorter focal length gives a wider field of view.
Used in Camera Modules for Arduino, ESP32, Raspberry Pi and Jetson · Camera Lenses for Embedded Cameras · FPV Cameras
How the chip talks to its flash memory. Most ESP-12 modules use QIO or DIO; ESP8285 modules must be flashed in DOUT mode.
Used in ESP8266 and ESP8285 Modules
Writing a new firmware image to a board, usually over USB or from an SD card, so the board runs different code.
Used in 3D Printer Mainboards
The drone's main board: an IMU plus a processor running firmware such as Betaflight that keeps the craft level and drives the ESCs.
Used in Drone Parts Explained · ESCs Explained · Flight Controllers
A level switch with a magnetic float that rises with the liquid and closes or opens a reed contact at a fixed height.
Used in Liquid Level Sensors
An input pin that is connected to nothing, so it picks up noise and reads random HIGH or LOW values. Fix it with a pull-up or pull-down resistor.
Used in Pull-Up and Pull-Down Resistors · Push Buttons with Arduino · Logic Gate ICs
A chemical that cleans metal surfaces and helps molten solder flow and bond.
Used in How to Solder Electronics · The Starter Electronics Toolkit · Hot Air Rework and SMD Soldering
A diode placed across a coil (relay, motor, solenoid) to absorb the voltage spike when current is switched off.
Used in DC Motors Explained · Motor Drivers Explained · Relay Modules
Frequency-modulated continuous wave radar: sweeps its frequency to measure the distance and motion of targets, including people sitting still.
Used in mmWave Radar Modules
The distance in millimetres from a lens to its focus point. Short focal lengths (2.8 mm) are wide angle, long ones (16 mm and above) zoom in.
Used in Camera Modules for Arduino, ESP32, Raspberry Pi and Jetson · Camera Lenses for Embedded Cameras
The voltage a diode or LED drops when conducting: about 0.7 V for silicon diodes, 1.8 to 3.3 V for LEDs.
Used in LEDs Explained · Series and Parallel Circuits · Diodes Explained
First-person view: flying a drone through a live video feed from an onboard camera, sent by a video transmitter (VTX) to goggles or a screen.
Used in Drone Parts Explained · Brushless Motor KV, Stator Size and Propeller Sizing Explained · Flight Controllers
Memory that holds a full image of a display before it is sent to the screen.
Used in SSD1306 OLED Display · TFT Displays for Arduino and ESP32 · E-Paper Displays
How many times per second a signal repeats, measured in hertz (Hz). 1 kHz is 1000 cycles per second.
Used in PWM Explained · PAM8403 and Other Audio Amplifier Modules · SPI Explained
The faceted plastic dome on a PIR sensor that focuses infrared from many zones onto the sensor.
Used in PIR Motion Sensor (HC-SR501)
Force-sensing resistor: a thin film whose resistance falls as pressure on it increases. Good for detecting presses, not for exact weights.
The largest value a sensor can measure, such as plus or minus 2 g or up to 65,535 lux. Smaller ranges give finer resolution.
Used in Accelerometers · Ambient Light Sensors
Acceleration measured relative to gravity. 1 g is 9.81 m/s2, the pull you feel standing still.
Used in Accelerometers
How much an amplifier multiplies its input. A gain of 10 turns a 0.1 V signal into 1 V. For an op-amp it is set by two resistors.
Used in Op-Amps for Beginners · PAM8403 and Other Audio Amplifier Modules · Load Cells and the HX711
Generic Attribute Profile, the structure Bluetooth LE uses to organise data into services and characteristics that phones can read, write or subscribe to.
Used in Bluetooth LE Modules
Pressure measured relative to the surrounding air. Absolute pressure is measured against a vacuum, and differential pressure between two ports.
Used in Pressure Transducers and Transmitters · MEMS and Differential Pressure Sensors · Airspeed and Telemetry Sensors for Drones and Planes
A motorised camera mount that keeps the camera steady and pointed as the aircraft moves, using an IMU and brushless motors.
Used in Drone Payloads
The temperature at which a plastic softens and loses stiffness (about 60 °C for PLA, 80 °C for PETG, 105 °C for ABS). Parts deform above it.
Used in PLA vs PETG vs ABS vs TPU · Filament Drying and Storage · PLA and PLA+ Filament
A camera sensor that exposes all pixels at the same moment, so fast motion does not skew. Rolling shutters read line by line.
Used in Camera Modules for Arduino, ESP32, Raspberry Pi and Jetson · Camera Lenses for Embedded Cameras · FPV Cameras
Global navigation satellite system: the general term covering GPS (USA), GLONASS, Galileo and BeiDou. Newer modules use several at once for a faster fix.
Used in NEO-6M GPS Module · Flight Controllers · Wi-Fi vs Bluetooth vs LoRa vs Zigbee
General-purpose input/output: a microcontroller pin that your code can read or drive.
Used in Arduino Uno · ESP32 Guide · Raspberry Pi Pico Guide
A 4-pin plug-and-play connector system from Seeed with ready-made sensor modules for I2C, UART, analog or digital signals.
Used in M5Stack Boards · Seeed XIAO Boards
A sensor that measures rotation rate, in degrees per second.
Used in MPU6050 Accelerometer and Gyroscope · Flight Controllers · Accelerometers
A circuit of four switches that can drive a motor in both directions.
Used in DC Motors Explained · Motor Drivers Explained · Stepper Motors and Drivers
A link where devices take turns sending on the same wires, as on RS485. A direction pin switches the driver between transmit and receive.
Used in Modbus RTU With Arduino and ESP32 · Serial Device Servers
The small voltage produced across a conductor or sensor in a magnetic field. Hall sensors use it to detect magnets or measure current without electrical contact.
Used in ACS712 vs INA219 Current Sensors · Hall Effect Sensors and Reed Switches · Motor Encoders and Speed Feedback
Distortions of a compass reading. Hard-iron comes from nearby magnets and currents; soft-iron comes from iron that bends the magnetic field. Calibration removes most of both.
Used in Magnetometers and 9-Axis IMUs
Hardware Attached on Top: a Raspberry Pi add-on board in the standard 65 x 56.5 mm size that plugs onto the 40-pin header and can identify itself to the OS.
Used in Raspberry Pi HATs Explained
The standard controller chip used in character LCDs such as 16x2 and 20x4 displays.
Used in 16x2 LCD with I2C · 128x64 Graphic LCD (ST7920)
Horizontal dilution of precision: a number from the GPS receiver showing how good the satellite geometry is. Lower is better; below about 2 is a good fix.
Used in Drone GPS, Compass and RTK Modules · GPS and GNSS Modules
The heated build plate of a 3D printer. It keeps the first layers warm so they stick and do not warp; PLA needs about 60 °C, ABS about 100 °C.
Used in PLA vs PETG vs ABS vs TPU · 3D Printer Bed Levelling and First-Layer Fixes · How to Choose a 3D Printer
A metal part that draws heat away from a component and releases it into the air.
Used in Voltage Regulators · Solid-State Relay vs Mechanical Relay · 3D Printer Hotends and Extruders Explained
The torque a powered stepper motor can resist without moving.
Used in Stepper Motors and Drivers · A4988 vs DRV8825 vs TMC2209 · 28BYJ-48 Stepper Motor with ULN2003 Driver
Absorbs moisture from the air. Nylon, TPU and PETG filaments do, which causes bubbles and stringing until they are dried.
Used in PLA vs PETG vs ABS vs TPU · 3D Printer Nozzles · Filament Drying and Storage
A deliberate gap between the switch-on and switch-off thresholds of a comparator or thermostat, so a noisy signal does not make the output chatter.
Used in Op-Amps for Beginners · Rain and Water Level Sensor Modules · Flame Sensor Modules
Inter-Integrated Circuit: a two-wire bus (SDA and SCL) that connects many devices by address.
Used in Arduino Uno · ESP32 Guide · I2C Explained
Inter-IC Sound: a serial bus for digital audio with a bit clock, a word-select clock and a data line, used by digital microphones and audio DACs.
Used in Sound Sensor and Microphone Modules Explained · I2S Microphones and Audio on ESP32
Beacon formats that broadcast a short identifier by Bluetooth LE. iBeacon uses a UUID, major and minor number; Eddystone uses a namespace and instance.
Used in BLE Beacons
Inertial measurement unit: a combined accelerometer and gyroscope, sometimes with a magnetometer.
Used in MPU6050 Accelerometer and Gyroscope · Flight Controllers · Legged Robots
A coil that stores energy in a magnetic field; the key part of buck and boost converters.
Used in Buck and Boost Converters · Inductors Explained
Light just beyond red that people cannot see, used by IR obstacle sensors, remote controls and line-following sensors.
Used in IR Obstacle Sensor Module · Line Follower Robot · MAX30102 Heart Rate and SpO2 Sensor Guide
Signal power lost in a cable, connector or adapter, given in decibels. Longer or thinner cable and more connectors lose more.
Used in RF Cables and Pigtails · Choosing an Antenna
A hardware signal that makes the microcontroller pause its program and run a short function immediately, for example when a button pin changes.
Used in Push Buttons with Arduino · Arduino Mega 2560 · UART and Serial Communication
A device that captures a computer's video and emulates its keyboard and mouse over the network, so you can control it remotely even before it boots.
Used in IP KVM
Ingress Protection rating (IEC 60529), such as IP65: the first digit rates protection against dust and solids, the second against water.
Used in Waterproof Ultrasonic Sensors · LED Strips · Project Enclosures, Standoffs and Screws
A solvent used to wash uncured resin from prints. It becomes contaminated with resin and must be replaced.
Used in Resin Wash and Cure Stations
A tiny snap-on RF connector for an external antenna. A module with an IPEX connector needs an antenna or pigtail fitted before it can transmit well.
Used in ESP8266 and ESP8285 Modules
A pattern projector in a depth camera that adds texture to plain walls so the stereo matching works better.
Used in Depth Cameras
Instruction set architecture: the set of instructions a processor understands. RISC-V is an open ISA that anyone can implement.
Used in RISC-V Development Boards
Ways to program AVR chips directly: ISP (in-system programming) uses six wires, and UPDI uses a single wire on newer ATtiny and ATmega parts.
Small locking connectors used on flight controllers, GPS and telemetry ports. SH is 1.0 mm pitch and GH is 1.25 mm pitch.
Used in XT30, XT60 and Drone Connectors
A short wire with pins or sockets on each end, used to connect parts on a breadboard or modules.
Used in How to Use a Breadboard · Jumper Wires and Dupont Connectors · Electronics Connectors
The number of pulses a flow meter outputs per litre. Divide the pulse rate by it to find the flow.
Used in Flow Sensors and Meters
A brushless motor's speed constant: RPM per volt with no load. A 2300 KV motor on a 4S (14.8 V) battery spins at about 34,000 RPM unloaded.
Used in Drone Parts Explained · Brushless Motor KV, Stator Size and Propeller Sizing Explained · ESCs Explained
A safety rating for lasers. Class 1 is safe in normal use; Class 2 (visible, under 1 mW) relies on the blink reflex; Class 3R and above can injure eyes.
Used in Laser Rangefinder Modules
How well each printed layer bonds to the one below it. Weak layer adhesion makes parts snap along layer lines.
Used in PLA and PLA+ Filament · PETG Filament · PEI Build Plates
Low-dropout regulator: a linear regulator that works with a small difference between input and output.
Used in Buck and Boost Converters · Li-ion, 18650 and LiPo Batteries · Voltage Regulators
Using 3-wire or 4-wire connections to an RTD so the resistance of the cable does not add error to the reading.
Used in PT100 and PT1000 RTD Sensors
Measuring distance by timing how long a pulse of light takes to bounce off an object and return.
In a 4-20 mA loop the lowest signal is 4 mA, not 0. A reading of 0 mA therefore means a broken wire or dead sensor.
Used in 4-20 mA and 0-10 V Signals
A metal bar or beam fitted with strain gauges whose resistance changes slightly as it bends under weight, used in digital scales.
Used in Load Cells and the HX711 · Load Cells and Strain Gauges
A circuit that powers the load straight from the charger input while the battery charges, so the charger IC is not confused by the load current. The bare TP4056 module lacks it.
Used in TP4056 Charger Module
A circuit that gives a HIGH or LOW output from one or more digital inputs according to a fixed rule, such as AND, OR, NOT, NAND, NOR or XOR.
Used in Logic Gate ICs · FPGA Boards for Beginners
The voltage that represents a digital high: 5 V on classic Arduinos, 3.3 V on ESP32, Pico and Raspberry Pi.
Used in Arduino Uno · ESP32 Guide · Raspberry Pi Pico Guide
A MOSFET that turns fully on with a gate voltage of 4.5 V or less, so a microcontroller can drive it.
Used in Transistors and MOSFETs as Switches · Solenoids and Linear Actuators · Mini Water Pumps for Arduino Projects
A network protocol built on LoRa radios: devices send to shared gateways, which forward data over the internet to a network server, with encryption and device management.
Used in Wi-Fi vs Bluetooth vs LoRa vs Zigbee · Antennas and RF Connectors · RF Cables and Pigtails
A switch placed between the load and ground; the easiest way to switch loads with NPN transistors and N-channel MOSFETs.
Used in Transistors and MOSFETs as Switches · Solenoids and Linear Actuators · Mini Water Pumps for Arduino Projects
A mid-speed LTE category (up to about 10 Mbit/s) used by many IoT modems because the chips are cheap and low power.
Used in 4G LTE Modules for IoT
The unit of illuminance, or how much light falls on a surface. Full daylight is around 10,000 to 100,000 lux; a lit room is about 300 to 500 lux.
Used in LDR Light Sensors · Ambient Light Sensors · BH1750 light sensor
Linear variable differential transformer: a coil-based sensor that gives a very accurate, contactless position along a short stroke.
Used in Linear Position Sensors
Light and Versatile Graphics Library, a free embedded GUI toolkit for building buttons, sliders and charts on small displays.
Used in ESP32-S3 Touchscreen Boards
Milliamp-hours: battery capacity. 2000 mAh can supply 2000 mA for one hour or 200 mA for ten hours, in theory.
Used in Li-ion, 18650 and LiPo Batteries · How to Power an Arduino or ESP32 from Batteries · LiPo Batteries for Drones
A smart-home standard that lets devices from different brands work together locally over Wi-Fi, Thread or Ethernet.
Used in Official Arduino Boards Compared
The lightweight message protocol used by ArduPilot and PX4 to exchange telemetry and commands with a ground station.
Used in Drone Telemetry Radios
NXP's development tools for its microcontrollers: an IDE, configuration tools and SDKs for each board.
Used in NXP FRDM Freedom Boards
A heated semiconductor whose resistance changes when gases such as alcohol, smoke or LPG touch it. The MQ-series are MOX sensors.
Used in Winsen Gas Sensor Modules
A single chip with a processor, memory and input/output pins that runs one program, such as the ATmega328P or ESP32.
Used in Arduino Uno · ESP32 Guide · Raspberry Pi Pico Guide
A SparkFun system of small processor boards that slide into a carrier board, so you can swap the microcontroller without rewiring.
Driving a stepper motor's coils with intermediate currents to divide each full step into smaller steps for smoother motion.
Used in Stepper Motors and Drivers · A4988 vs DRV8825 vs TMC2209 · 28BYJ-48 Stepper Motor with ULN2003 Driver
NXP's family of 13.56 MHz contactless cards and fobs (MIFARE Classic 1K is the usual one) read by the RC522.
Used in RC522 RFID Reader · NFC Readers and Tags
Motion JPEG: a video stream made of individual JPEG frames, the format the ESP32-CAM streams to a browser.
Used in ESP32-CAM · Raspberry Pi Camera Modules · Camera Modules for Arduino, ESP32, Raspberry Pi and Jetson
A simple industrial request-and-reply protocol in which a master polls numbered registers on slave devices, usually over RS-485 (Modbus RTU) or Ethernet (Modbus TCP).
Used in PZEM-004T AC Energy Meter Module with ESP32 · RS-485 and RS-232 Modules · Weather Station Sensors
A 555 timer mode with one stable state: a trigger produces a single timed pulse.
Used in 555 Timer IC
Metal-oxide-semiconductor field-effect transistor, controlled by gate voltage. Efficient for switching large currents.
Used in Transistors and MOSFETs as Switches · ESCs Explained · Schematic Symbols
Message Queuing Telemetry Transport: a lightweight publish/subscribe messaging protocol where devices send and receive messages on named topics through a broker.
Used in MQTT and Home Assistant for ESP32 · ESP-NOW · Ethernet Modules
Driving several displays or LEDs from a few pins by switching between them faster than the eye can see.
Used in 7-Segment Displays · MAX7219 LED Dot Matrix · 74HC595 Shift Register
A microcontroller with USB built into the chip, so the board can act as a keyboard, mouse or MIDI device instead of only a serial port.
Used in Pro Micro (ATmega32U4)
NFC Data Exchange Format: a standard way to store a URL, text or contact on an NFC tag so phones can read it.
Used in NFC Readers and Tags
Non-dispersive infrared: the accurate way to measure CO2 by absorption of infrared light, used by sensors such as the MH-Z19 and SCD40.
Used in MQ Gas Sensors · Air Quality Sensors · VOC and Indoor Air Quality Sensors
Near-field communication: the 13.56 MHz standard used by phones and contactless cards. The RC522 reads MIFARE cards but not every NFC tag type.
Used in RC522 RFID Reader · NFC Readers and Tags · RFID Readers and Tags
The plain-text sentence format (lines starting with $GPGGA, $GPRMC) that GPS modules send over serial.
Used in NEO-6M GPS Module · PM2.5 and PM10 Dust Sensors · Drone GPS, Compass and RTK Modules
A battery's typical voltage during discharge, such as 3.7 V for a Li-ion cell.
Used in Li-ion, 18650 and LiPo Batteries · How to Power an Arduino or ESP32 from Batteries · LiPo Batteries for Drones
A switch or relay contact that conducts until it is pressed or energised (NC), the opposite of normally open (NO).
Used in Push Buttons with Arduino · Limit Switches and Micro Switches · Inductive and Capacitive Proximity Sensors (NPN, PNP)
Neural processing unit: a block of hardware that runs neural-network maths faster and with less power than the main CPU.
Used in TinyML and AI Vision Kits
A fast SSD standard using PCIe. The Raspberry Pi 5 can boot from an NVMe drive through a HAT.
Used in Raspberry Pi 5 Guide · Raspberry Pi HATs Explained · Raspberry Pi Cases and Cooling
External RAM chip on eight data lines. ESP32-S3 boards with names like N8R8 carry 8 MB of flash and 8 MB of octal PSRAM for images, audio and AI models.
V = I x R: voltage equals current times resistance.
Used in Resistors Explained · LEDs Explained · Ohm's Law and Power
Organic LED display: each pixel emits its own light, so there is no backlight and blacks are truly black.
Two ways to send data over radio: on-off keying switches the carrier on and off, frequency-shift keying moves between two frequencies.
Used in CC1101 and Sub-GHz Transceivers
Operational amplifier: an IC with two inputs and one output that amplifies the difference between them, used for sensor amplifiers, filters, buffers and comparators.
Used in Op-Amps for Beginners · Schematic Symbols · Comparators
An output that can only pull LOW; it needs a pull-up resistor to go HIGH. Many sensor modules and the LM393 comparator work this way.
Used in IR Obstacle Sensor Module · Optocouplers · ULN2003 Darlington Array
An output that can only pull a line low; a pull-up resistor makes it high. Used by I2C.
Used in I2C Explained · 3.3 V vs 5 V Logic · Pull-Up and Pull-Down Resistors
The on-board debug and programming interface on NXP boards, so no external probe is needed.
Used in NXP FRDM Freedom Boards
A component that passes a signal through light between an LED and a phototransistor, electrically isolating two circuits.
Used in Relay Modules · Optocouplers · Solid-State Relay vs Mechanical Relay
Over-the-air activation: a LoRaWAN node joins the network by exchanging keys (DevEUI, AppEUI/JoinEUI, AppKey) and gets fresh session keys each time it joins.
Used in LoRaWAN Nodes and Gateways
Tiny solid or liquid particles in the air. PM2.5 means particles up to 2.5 micrometres across, PM10 up to 10 micrometres.
Used in PM2.5 and PM10 Dust Sensors
PCI Express, a fast serial link used for NVMe drives and AI accelerators. The Raspberry Pi 5 exposes one PCIe lane through a small flat-cable connector.
Used in Raspberry Pi HATs Explained · Raspberry Pi Compute Modules
One high-speed data path of the PCI Express bus. Raspberry Pi 5 exposes a single lane for NVMe drives and other add-in boards.
Used in Raspberry Pi 5 NVMe and PCIe
Polyetherimide, a heat-resistant plastic sheet used as a 3D printer build surface because many filaments stick to it hot and release when it cools.
Glycol-modified PET, a 3D printing plastic that is tougher and more heat tolerant than PLA, prints at 230 to 250 °C and tends to string.
Used in PETG Filament
A laser distance method that measures the phase difference of a modulated beam. It gives millimetre accuracy over tens of metres.
Used in Laser Rangefinder Modules
A diode that produces a small current in proportion to light. Faster and more linear than an LDR, used in IR receivers and light meters.
Used in IR Obstacle Sensor Module · MAX30102 Heart Rate and SpO2 Sensor Guide · Flame Sensor Modules
Building a 3D model from many overlapping photos, using software to find matching points.
Used in 3D Scanners
An infrared LED and a phototransistor facing each other across a slot. An object in the slot blocks the light and changes the output.
A liquid plastic that hardens when exposed to UV light. Resin 3D printers cure it layer by layer with a UV screen or laser.
Used in Standard, Water-Washable and ABS-Like Resins for MSLA Printers · Engineering Resins · Resin Vats, FEP, PFA and ACF Film
Another name for an LDR: a resistor whose resistance drops as light increases.
Used in LDR Light Sensors · Ambient Light Sensors
Proportional-integral-derivative control: a feedback loop that steers towards a target smoothly by combining the current error, its history and its rate of change.
Used in Line Follower Robot · Drone Parts Explained · Flight Controllers
A calibration run in which the firmware measures how a heater responds and sets values so the temperature holds steady without overshooting.
Used in Hotend Parts · Drone Payloads
A ceramic element that bends when voltage is applied (and makes a voltage when bent), used in passive buzzers and vibration sensors.
Used in Active vs Passive Buzzers · Sound Sensor and Microphone Modules Explained · Vibration, Shock and Tilt Sensors (SW-420, SW-520D)
A ceramic disc that converts electrical signals into vibration and vibration into electrical signals; it is the part inside 40 kHz ultrasonic sensors.
Used in 40 kHz Ultrasonic Transducers
A short cable with a small connector (such as U.FL) on one end and a larger one (such as SMA) on the other, used to bring an antenna connection out of a board.
Used in RF Cables and Pigtails · Choosing an Antenna
Programmable I/O: small state machines on the RP2040 and RP2350 that generate or read precise signals independently of the CPU.
Used in Raspberry Pi Pico Guide · How to Choose a Microcontroller Board · RP2040 and RP2350 Boards Beyond the Pico
Passive infrared: a sensor that detects changes in infrared heat, such as a person walking past.
Used in PIR Motion Sensor (HC-SR501) · mmWave and Microwave Presence Sensors · mmWave Radar Modules
A very low VTX power setting used on the ground so you do not jam other pilots' video.
Used in FPV Video Transmitters (VTX)
A small tube pointing into the airflow that measures total pressure. Together with the static pressure it gives airspeed.
Used in Airspeed and Telemetry Sensors for Drones and Planes
The width of one photosite, in micrometres. Bigger pixels gather more light and give cleaner low-light pictures.
Used in Camera Image Sensors Explained
Polylactic acid, the most common 3D printing plastic: easy to print at 190 to 220 °C, low warp, but it softens at about 55 to 60 °C.
Used in PLA and PLA+ Filament
Industrial sensor outputs that switch the positive supply (PNP) or ground (NPN) to the load. The type must match your input.
Used in Photoelectric Sensors
A set of 3D points captured by a scanner. It is turned into a surface mesh before printing or editing.
Used in 3D Scanners
A tough, wear-resistant plastic. PA6 and PA12 are common in 3D printing. They absorb moisture and must be dried before printing.
Exposing a washed resin print to UV light for a few minutes so it reaches full strength and is no longer sticky.
Used in Standard, Water-Washable and ABS-Like Resins for MSLA Printers · Engineering Resins · Resin Vats, FEP, PFA and ACF Film
The rate of energy use, in watts (W). P = V x I, so a 12 V load drawing 2 A uses 24 W.
Used in Ohm's Law and Power · Choosing a Power Supply · Solid-State Relay vs Mechanical Relay
Feeding power into a long LED strip at several points to prevent voltage drop and colour shift.
Used in WS2812B Addressable LEDs (NeoPixel) · P10 LED Matrix Panels · LED Strips
Photoplethysmography: measuring pulse by shining light into skin and detecting the small changes in light absorbed as blood volume rises and falls.
Parts per million. Used for gas concentration (outdoor CO2 is about 420 ppm) and for frequency accuracy: a 20 ppm crystal can drift about 1.7 seconds a day.
Used in MQ Gas Sensors · Crystals and Oscillators · DS3231 vs DS1307 Real-Time Clock Modules
Pulses per revolution (PPR) is the number of cycles on one channel per turn. Counts per revolution (CPR) is what a controller counts after decoding both channels and all edges, normally 4 times PPR.
How far a propeller would advance in one turn through a soft medium, in inches. Higher pitch moves more air per turn but needs more power.
Used in Drone Propellers
A motor direction layout where the front propellers spin outward over the top, now common in freestyle flying.
Used in Drone Propellers
Extra RAM on some ESP32 boards (4 or 8 MB) used for camera frames and large buffers.
Used in ESP32-CAM · ESP32 vs ESP8266 · TFT Displays for Arduino and ESP32
A heating element whose resistance rises sharply with temperature, so it limits its own temperature without a thermostat.
Used in PTC Heaters and Heating Elements
Polytetrafluoroethylene: a slippery, heat-resistant plastic used for Bowden tubes and hotend liners. It starts to degrade above about 260 °C.
A resistor from an input pin to ground so the pin reads LOW until something drives it HIGH.
Used in Pull-Up and Pull-Down Resistors · USB Cables and Connectors
A resistor from a signal line to the supply that keeps the line high when nothing pulls it low.
Used in I2C Explained · 3.3 V vs 5 V Logic · DHT11 vs DHT22
A throwaway block printed beside a multi-colour model to flush the old colour from the nozzle before the next one.
A connector where a tube is pushed in and a collet grips it. Squeezing the collet releases the tube.
Pulse-width modulation: switching a signal on and off quickly so its average sets brightness, speed or position.
Used in Arduino Uno · Raspberry Pi Pico Guide · HC-SR04 Ultrasonic Sensor
Two square-wave signals 90 degrees apart (A and B). Which one changes first tells the direction of rotation.
Used in Optical, Magnetic and Absolute Rotary Encoders · KY-040 / EC11 Rotary Encoder Module
The current a regulator or chip draws for itself with no load.
Used in Voltage Regulators · Solar Panels and Charge Controllers for Electronics Projects · E-Paper Displays
A thermal camera that gives a temperature for every pixel, not just a picture. Non-radiometric cameras only show relative contrast.
Used in Thermal Cameras
An op-amp whose output can swing almost all the way to both supply voltages. Older parts such as the LM741 and LM358 cannot reach the positive rail.
Used in Op-Amps for Beginners
An analog output that is a fraction of the supply voltage, so the reading changes if the supply changes unless the ADC uses the same reference.
A resistor and capacitor in series that smooths a signal, turning PWM into a steady voltage or removing high-frequency noise.
Used in PWM Explained · PAM8403 and Other Audio Amplifier Modules · Rotary Encoders
A MOSFET's resistance when fully on; lower means less heat.
Used in Transistors and MOSFETs as Switches · How to Read a Datasheet · MOSFET Gate Drivers and Driver Modules
How far a reader can detect a tag. It depends on reader power, antenna, tag type, orientation and what the tag is stuck to.
Used in RFID Readers and Tags
A diode or bridge that converts AC into pulsing DC by letting current pass in one direction only.
Used in Diodes Explained · AC vs DC · Mains Step-Down Transformers for DC Power Supplies
The amount of water vapour in air as a percentage of the maximum it can hold at that temperature.
Used in DHT11 vs DHT22 · BME280 vs BMP280 · How to Choose a Temperature Sensor for Arduino and ESP32
An electrically operated switch: a coil moves contacts that switch a separate circuit.
Used in Relay Modules · Schematic Symbols · MQTT and Home Assistant for ESP32
A broadcast from a drone that shares its identity and position so authorities can identify it in flight; rules differ by country.
Used in Drone Navigation Lights, Strobes and Lost-Model Alarms
How much a part opposes current, measured in ohms (Ω). V = I x R links it to voltage and current.
Used in Ohm's Law and Power · Wire Gauge Guide · Force Sensitive Resistors (FSR)
The smallest step a measurement or output can represent. A 12-bit ADC on 3.3 V has steps of about 0.8 mV.
Used in PWM Explained · ADCs Explained · BME280 vs BMP280
The frequency at which a piezo element or LC circuit responds most strongly. A passive buzzer is loudest near it, often 2 to 4 kHz.
Used in Active vs Passive Buzzers · 40 kHz Ultrasonic Transducers
A small backward move of the filament that relieves pressure in the nozzle before a travel move, so the printer does not leave strings.
Used in TPU and Flexible Filament · 3D Printer Maintenance and Tools
The same match information as VSWR given in decibels. A larger number means less power is reflected.
Used in Choosing an Antenna
Radio-frequency identification: reading a small tag's ID wirelessly. Hobby readers use 125 kHz (EM4100) or 13.56 MHz (RC522, PN532).
Used in RC522 RFID Reader · NFC Readers and Tags · RFID Readers and Tags
A potentiometer wired with only two terminals so it acts as a variable resistor rather than a voltage divider.
Used in Potentiometers and Trimmers
Small leftover AC variation on a DC supply, especially from switching converters.
Used in Buck and Boost Converters · Capacitors Explained · AC vs DC
An open instruction set used in newer ESP32 chips (C3, C6, H2) and in the second CPU option of the RP2350.
Used in ESP32-S3, C3, C6 and Other ESP32 Variants · RISC-V Development Boards · Alternatives to Raspberry Pi
A tool that lets a computer write to the eMMC of a Raspberry Pi Compute Module over USB.
Used in Raspberry Pi Compute Modules
Received signal strength indicator: how strong a radio signal is at the receiver. It falls with distance but is easily disturbed, so it gives only rough range.
Used in BLE Beacons · UWB Modules
Real-time clock: a chip that keeps the date and time running, usually from a coin cell when main power is off.
The standard message format for correction data sent from a base station to an RTK rover.
Resistance temperature detector: a platinum element (PT100, PT1000) whose resistance rises in a very repeatable way with temperature.
Used in PT100 and PT1000 RTD Sensors
Real-time kinematic positioning. A fixed base station sends corrections to a rover GNSS receiver, which can then locate itself to a few centimetres.
Used in Drone GPS, Compass and RTK Modules · Pixhawk and ArduPilot Autopilots · GPS and GNSS Modules
How many measurements per second an ADC, logic analyzer or audio device takes. To capture a signal reliably, sample several times faster than its fastest change.
Used in Voice Recognition and Recording Modules (ISD1820, LD3320) · Logic Analyzers · ECG, EMG and EEG Sensors
Single-board computer: a complete computer on one board, such as the Raspberry Pi, that runs a full operating system.
Used in Raspberry Pi 5 Guide · Arduino vs Raspberry Pi · How to Choose a Microcontroller Board
An input with hysteresis: it switches HIGH at one voltage and back LOW at a lower one, which turns slow or noisy signals into clean digital edges.
Used in Logic Gate ICs
A diode with a low forward drop (about 0.2 to 0.4 V) and fast switching, such as the 1N5819, used for reverse protection and in switching converters.
Used in Diodes Explained · Schematic Symbols · Fuses, PTC Resettable Fuses and TVS Diodes
A radio whose tuning and decoding are done in software. A cheap USB dongle can listen to a wide range of frequencies.
Used in SDR Receivers
Air pressure corrected to sea level, used as the reference when turning a pressure reading into altitude. The standard value is 1013.25 hPa.
Used in Barometric Pressure Sensors
How much signal a load cell gives per volt of excitation at full load. A 2 mV/V cell on 5 V gives 10 mV at its rated capacity.
Used in Load Cells and Strain Gauges
Combining accelerometer, gyroscope and magnetometer data to get a stable orientation that is better than any single sensor.
Used in Magnetometers and 9-Axis IMUs
A box that connects a serial device (RS232 or RS485) to a network so software on another computer can talk to it over TCP or UDP.
Used in Serial Device Servers
In series, parts are in one chain and share current; in parallel, they share the same two nodes and voltage.
Used in How to Use a Multimeter · Ohm's Law and Power · Series and Parallel Circuits
A motor with built-in position feedback that moves to an angle set by a pulse signal.
Used in Servo Motors Guide · PCA9685 16-Channel Servo Driver · How to Choose a Motor for a Robot or Project
An Arduino add-on board that plugs onto the headers of an Uno or Mega to add features such as a motor driver, Ethernet or an LCD.
Used in Arduino Shields
A scale for how hard a rubber or flexible plastic is. Flexible filaments are quoted on Shore A (for example 95A); lower numbers are softer.
Used in TPU and Flexible Filament
A low-value, accurate resistor placed in series with a load so the current can be calculated from the small voltage across it.
Used in ACS712 vs INA219 Current Sensors · Panel Voltmeters, Ammeters and Current Shunts · 4-20 mA and 0-10 V Signals
A small open-source telemetry modem (433 or 915 MHz) used to link a flight controller to a ground station over MAVLink.
Used in Drone Telemetry Radios
Single-wire protocols that let a flight controller change a VTX's channel and power from the OSD menu or the radio.
Used in FPV Video Transmitters (VTX)
Surface-mount device: a small component soldered onto the surface of a PCB rather than through holes.
Used in Resistor Colour Code Chart · PCB Basics · Hot Air Rework and SMD Soldering
A bimetal disc that flips quickly from one curved shape to the other at a set temperature, opening or closing contacts with a click.
Used in Bimetal Thermostat Switches
Fixing a flight controller on rubber grommets or gel so motor vibration does not reach the gyro.
Used in Drone Dampers, Standoffs, Clamps and Landing Gear · FC and ESC Stacks and AIO Boards
Unwanted solder joining two neighbouring pins or pads.
Used in How to Solder Electronics · Perfboard and Stripboard · PCB Basics
A bottle of gas with a known concentration used to calibrate a gas sensor at its upper range.
Used in Electrochemical Gas Sensors · Winsen Gas Sensor Modules
Serial Peripheral Interface: a fast bus with clock, data in, data out and a chip-select line per device.
Used in Arduino Uno · ESP32 Guide · I2C Explained
Peripheral blood oxygen saturation: the percentage of haemoglobin carrying oxygen, estimated by pulse oximeters from red and infrared light absorption.
Serial Port Profile: the Bluetooth Classic profile that makes the HC-05 look like a wireless serial cable to a phone or PC.
Used in HC-05 Bluetooth Module · Wi-Fi vs Bluetooth vs LoRa vs Zigbee
A LoRa setting from SF7 to SF12. A higher value gives longer range but a lower data rate and more airtime for each message.
Used in LoRaWAN Nodes and Gateways
Solid-state relay: an electronic switch with no moving parts, controlled like a relay.
Used in Relay Modules · AC vs DC · Solid-State Relay vs Mechanical Relay
ST's programmer and debugger for STM32 chips. Nucleo and Discovery boards carry one on the board.
The current a motor draws when its shaft is blocked; the maximum it will draw.
Used in DC Motors Explained · Motor Drivers Explained · Servo Motors Guide
The remaining battery capacity as a percentage.
Used in Battery Monitors and Fuel Gauges
A three-term equation that converts an NTC thermistor's resistance to temperature more accurately than the beta equation over a wide range.
Used in NTC Thermistors
A motor that moves in fixed angular steps, allowing precise positioning without feedback.
Used in Stepper Motors and Drivers · A4988 vs DRV8825 vs TMC2209 · 28BYJ-48 Stepper Motor with ULN2003 Driver
The chip on a printer mainboard (such as TMC2209) that turns step and direction signals into current in the motor coils.
Used in 3D Printer Mainboards
Measuring distance by comparing two camera images, like human eyes. Many depth cameras add an infrared projector to help on plain surfaces.
Used in Depth Cameras
The resting voltage for storing LiPo and Li-ion cells, about 3.8 V per cell, which reduces ageing.
Used in LiPo Chargers, Smoke Stoppers and Battery Safety for Drones
A pin whose level at reset selects a boot mode, such as GPIO 0, 2, 12 and 15 on the ESP32.
Used in ESP32 Guide · ESP8266 NodeMCU · ESP32-CAM
Serial Wire Debug: a two-wire (SWDIO and SWCLK) debug and programming interface on Arm Cortex-M microcontrollers such as STM32 and RP2040.
Used in Programmers and Debug Probes · STM32 Nucleo and Discovery Boards · RP2040 and RP2350 Boards Beyond the Pico
The gap between the temperature (or level) at which a switch trips and the one at which it resets, which stops it chattering on and off.
Used in Bimetal Thermostat Switches
The type of barcode, for example Code 128, EAN-13 or QR. A scanner must have the symbology enabled to read it.
Aluminium profile with grooves that take sliding T-nuts and bolts, used to build printer frames, CNC machines and workbenches.
Used in Aluminium Extrusion Profiles
How a potentiometer's resistance changes with rotation: linear (B) changes evenly, logarithmic or audio (A) changes slowly at first and faster at the end.
Used in Potentiometers and Trimmers
Setting a scale's reading to zero with a container or platform in place, so only the added weight is measured.
Used in Load Cells and the HX711 · Load Cells and Strain Gauges
Open-source firmware for ESP8266 and ESP32 smart devices that adds a web interface, MQTT and local control instead of a cloud app.
Used in Wi-Fi Smart Switches and Relays
Temperature-compensated crystal oscillator: a crystal oscillator that corrects its frequency for temperature, giving a clock accurate to a few ppm.
Used in DS3231 vs DS1307 Real-Time Clock Modules · SDR Receivers
How many degrees a part or heatsink warms per watt of heat flowing through it, in °C/W. Lower is better: a 2 °C/W heatsink carrying 10 W runs about 20 °C above ambient.
Used in Heatsinks, Fans and Thermal Paste · Peltier Modules (TEC1-12706) · Bimetal Thermostat Switches
Firmware safety that stops a printer if a heater is on but the temperature is not rising as expected, for example when a thermistor falls out.
Used in Hotend Parts · 3D Printer Maintenance and Tools · PTFE Tubing and Pneumatic Fittings for 3D Printers
A chip slowing itself down when it gets too hot. The Raspberry Pi starts throttling at about 80 °C.
Used in Raspberry Pi Cases and Cooling
A set of thermocouples that generates a small voltage from infrared heat. It is the sensing element in non-contact IR thermometers.
Used in Thermal Imaging Modules
Total motor thrust divided by the aircraft weight. A multirotor needs at least 2 to 1 to fly safely, with the hover at about half throttle.
Used in Heavy-Lift Drone Motors and Prop Combos · Drone Payloads
τ = R x C: the time for an RC circuit to charge to about 63% of the supply.
Used in Capacitors Explained · 555 Timer IC · Supercapacitors
Measuring distance from how long a signal (sound or light) takes to bounce back.
Used in HC-SR04 Ultrasonic Sensor · VL53L0X and VL53L1X Laser Distance Sensors · Waterproof Ultrasonic Sensors
How long a GPS module takes to report a position after power-up: a minute or more from cold, seconds when its backup battery has kept the almanac.
Used in NEO-6M GPS Module · Drone GPS, Compass and RTK Modules · GPS and GNSS Modules
A toothed belt that moves a printer axis without slipping. GT2 has a 2 mm tooth pitch.
Used in GT2 Timing Belts and Pulleys · Aluminium Extrusion Profiles
Learning by taking things apart, building and testing, without a fixed recipe: try, observe, change and try again.
Used in Atal Tinkering Lab (ATL) · How to Set Up a School Tinkering Lab · Ten First Lessons with ATL Package 1
Coating a soldering iron tip or wire with a thin layer of solder to improve heat transfer.
Used in How to Solder Electronics · Wire Gauge Guide · Perfboard and Stripboard
Running small machine-learning models on a microcontroller using only milliwatts and kilobytes of memory, for tasks such as keyword spotting and simple image classification.
Used in TinyML and AI Vision Kits
A rain gauge with a small see-saw bucket that tips each time a fixed amount of rain collects, sending one pulse per tip.
Used in Weather Station Sensors
How far a component's actual value may differ from its marked value, such as ±5%.
Used in Resistors Explained · Resistor Colour Code Chart · Capacitor Code Chart
Turning force, in N·m or kg·cm.
Used in DC Motors Explained · Servo Motors Guide · Brushless Motor KV, Stator Size and Propeller Sizing Explained
An op-amp circuit that turns the tiny current from a photodiode into a usable voltage.
A semiconductor switch that conducts in both directions once triggered, used to switch or dim AC loads. It turns off by itself when the current falls to near zero.
Used in AC Dimmers, Triacs and SCRs
A multimeter feature that measures the real effective value of non-sinusoidal AC.
Used in How to Use a Multimeter · AC vs DC · ACS712 vs INA219 Current Sensors
A table listing every combination of a logic circuit's inputs and the output each one produces.
Used in Logic Gate ICs · FPGA Boards for Beginners
Television lines: a rough measure of analog camera sharpness. 1200 TVL is common in FPV cameras.
Used in FPV Cameras
A UWB method where two devices exchange messages and calculate their distance from the round-trip time.
Used in UWB Modules
Universal asynchronous receiver-transmitter: two-wire serial (TX and RX) used by GPS, Bluetooth modules and debug output.
Used in Arduino Uno · I2C Explained · Arduino vs Raspberry Pi
Universal battery elimination circuit: a switching regulator that turns drone battery voltage into a steady 5 V or 12 V for receivers, servos and cameras.
Used in Drone PDBs and BECs · Drone Payloads · XT30, XT60 and Drone Connectors
u-blox's binary message format for configuring and reading GNSS receivers, more compact than NMEA text.
A firmware file format: drag a .uf2 file onto the Pico's USB drive to program it.
Used in Raspberry Pi Pico Guide · Programmers and Debug Probes · RP2040 and RP2350 Boards Beyond the Pico
The unique ID burned into an RFID tag, usually 4 or 7 bytes, that a reader uses to tell tags apart.
Used in RC522 RFID Reader · NFC Readers and Tags
Sound above human hearing (over 20 kHz); the HC-SR04 uses 40 kHz.
Used in HC-SR04 Ultrasonic Sensor · Waterproof Ultrasonic Sensors · Liquid Level Sensors
A Raspberry Pi warning shown when the supply voltage drops below about 4.63 V, usually from a weak adapter or thin cable.
A USB-C standard where the charger and device negotiate voltage and current. Raspberry Pi 5 uses it to request 5 A at 5 V.
Hardening resin with ultraviolet light, usually 405 nm, so the print reaches full strength.
Used in Resin Wash and Cure Stations
A radio that uses very short pulses over a wide band. It measures time of flight, so it can find position to within centimetres.
Used in UWB Modules
Volatile organic compounds: gases released by paints, cleaners, cooking and people. Indoor air sensors report a VOC index or a TVOC value.
Electrical pressure between two points, measured in volts (V). It pushes current through a resistance.
Used in Ohm's Law and Power · AC vs DC · Choosing a Power Supply
Two resistors in series that output a fixed fraction of the input voltage.
Used in 3.3 V vs 5 V Logic · HC-SR04 Ultrasonic Sensor · Resistors Explained
On stepper drivers, the reference voltage that sets the coil current limit.
Used in Stepper Motors and Drivers · ADCs Explained · A4988 vs DRV8825 vs TMC2209
Voltage standing wave ratio: how well an antenna matches the radio. 1:1 is perfect; below about 2:1 is acceptable. Poor VSWR reflects power back and can damage a transmitter.
Used in Choosing an Antenna
Video transmitter: the radio on a drone that sends the camera picture to the pilot's goggles, usually on 5.8 GHz.
Used in FPV Video Transmitters (VTX) · FPV Goggles and Video Receivers
Corners of a print lifting from the bed as the plastic cools and shrinks. Common with ABS and ASA, cured with a hot bed, an enclosure and a good first layer.
Used in Silk, Wood, Matte and Specialty PLA Filaments · ABS, ASA and HIPS Filament · Nylon, PC and Carbon Fibre Filaments
Four resistances arranged in a diamond so that a tiny change in one gives a measurable voltage difference across the middle. Load cells and many pressure sensors use it.
Used in Load Cells and the HX711 · Pressure Transducers and Transmitters · Load Cells and Strain Gauges
The diagonal distance between opposite motor shafts on a multirotor frame, in millimetres. It limits the largest propeller the frame can carry.
Used in FPV and Multirotor Drone Frames · Drone Frame Arms, Carbon Tubes, Motor Mounts and Canopies · Drone Dampers, Standoffs, Clamps and Landing Gear
The moving middle contact of a potentiometer that picks off the variable voltage.
Used in Potentiometers and Trimmers · Joystick Modules
Gold-plated bullet-pin power connectors rated roughly 30 A and 60 A continuous. The numbers in the name are the approximate current in amps.
Used in XT30, XT60 and Drone Connectors
The small distance between where the probe triggers and where the nozzle actually touches the bed, set so the first layer is the right height.
A diode designed to conduct in reverse at a fixed voltage (for example 5.1 V), used as a simple voltage reference or clamp.
Used in Diodes Explained · Schematic Symbols · Fuses, PTC Resettable Fuses and TVS Diodes
The instant an AC waveform passes through 0 V. Dimmers time their firing from it, and zero-cross relays switch on there to reduce interference.
Used in AC Dimmers, Triacs and SCRs